Here is when Magic happen!! You can turn steel wire Shelves into CNC machine.
we will finish the Rail system for Pararack in this stage.
You will need this parts
Part List
Screw
M8 40mm X 8
M8 Wing Nut X8
M4 30mm X8
M4 Wind Nut X8
Screw
M8 40mm X 8
M8 Wing Nut X8
M4 30mm X8
M4 Wind Nut X8
X Axis Clamp
Just like lock clip, it's is really easy to put X axis rod holder on, but the main problem would be to set it on right direction.
X rod holder content two different parts(as Picture#1)
the smaller Clamp one has thread on it, so it can hold it on to rod.
fasten those screw and wing nut according to the size of holes.
the best angle to see it in right order (as pic#8)
X rod holder content two different parts(as Picture#1)
the smaller Clamp one has thread on it, so it can hold it on to rod.
fasten those screw and wing nut according to the size of holes.
the best angle to see it in right order (as pic#8)
X Axis: 16mm Steel Rods & Liner bearing
Part List
M4 30mm X4
M4 WingNut X4
16mm Rod(lengths are according to rack size) X2
16mm Leaner Bearing X4
Lublican X1
1. After X Axis Holder are in the place, we could slide the 16mm rod into the upper hole of the holder.(pic#3)
2. when you slide the rod in, don't slide it all the way down to the other side of the holder, cuz we need to put the 16mm Linear bearing first.(pic#4)
3. once Linear bearings are in place, apply some lubrication can smooth the motion out.
4. to fasten these 16mm Rods, we just need one set of screw and wing nut. Hold the screw like (pic#7)
M4 30mm X4
M4 WingNut X4
16mm Rod(lengths are according to rack size) X2
16mm Leaner Bearing X4
Lublican X1
1. After X Axis Holder are in the place, we could slide the 16mm rod into the upper hole of the holder.(pic#3)
2. when you slide the rod in, don't slide it all the way down to the other side of the holder, cuz we need to put the 16mm Linear bearing first.(pic#4)
3. once Linear bearings are in place, apply some lubrication can smooth the motion out.
4. to fasten these 16mm Rods, we just need one set of screw and wing nut. Hold the screw like (pic#7)
单击此处进行编辑.
Part List
Y Axis Holder X2
Y Axis Holder Washer X4
Zip ties X4
M4 30mm X8
M4 Wing Nut X8
12mm Rod(lengths are according to rack size) X2
1.Y Axis Holder mounting it's relative easy, just put it on 16mm linear bearing and fasten it with releasable zip ties.(pic#2&3)
2. before mounting the 12mm rods, the Linear Bearing needs to be slided in.(pic#7)
3. the small 2 hole washer to grip the 12mm rods.(pic#9)
4. don't tighten the holder just yet
Y Axis Holder X2
Y Axis Holder Washer X4
Zip ties X4
M4 30mm X8
M4 Wing Nut X8
12mm Rod(lengths are according to rack size) X2
1.Y Axis Holder mounting it's relative easy, just put it on 16mm linear bearing and fasten it with releasable zip ties.(pic#2&3)
2. before mounting the 12mm rods, the Linear Bearing needs to be slided in.(pic#7)
3. the small 2 hole washer to grip the 12mm rods.(pic#9)
4. don't tighten the holder just yet